@article { author = {Jabarpoor, A. R. and Javanmardi, J. and Roostaei, M. and Nasrifar, Kh. and Parvasi, P. and Alavi, F. and Jokar, S. M.}, title = {Possibility of Gas Heater Elimination for City-Gate Gas Stations in Hot-Climate Regions of Fars Province}, journal = {Iranian Chemical Engineering Journal}, volume = {19}, number = {113}, pages = {62-73}, year = {2021}, publisher = {Iranian Association of Chemical Engineering}, issn = {1735-5400}, eissn = {2008-2797}, doi = {}, abstract = {In common natural gas pressure reducing stations, gas heaters and throttle valves are used for pre-heating and pressure reducing. The gas heaters are used to prevent the hydrate formation after the station because of temperature reduction. In this work, in addition to study the existence of gas heaters in common stations, four substitute methods are presented and together with the commonly used method are simulated for 5 hot-climate cities in Fars province, i.e., Darab, Lar, Lamerd, Mohr and Farashband. These four methods are comprised of: 1- Use of an expansion turbine in place for the throttle valve, 2- Use of an expansion turbine for pressure reduction and an electric heater instead of the gas-burning heater, 3- Use of a vortex tube for the throttle valve, 4- Use of an evaporation-condensation cycle instead for the gas-burning heater. Heating loads and gas consumption for the commonly used method and suggestive methods are compared. Furthermore, the work gained through the use of the expansion turbine was calculated and reported. The expansion turbine and vortex tube need most and least heating loads and gas consumptions for preheating, respectively. The expansion-condensation cycle need lower heating load because of its higher efficiency in comparison of the direct gas-burning heater}, keywords = {City-Gate Gas Stations,Throttle Valve,Expansion Turbine,Electrical Heater,Vortex tube,CWT Heater}, title_fa = {امکان حذف گرم‌کن‌های گازی در ایستگاه‌های ورودی گاز شهری مناطق گرمسیر استان فارس}, abstract_fa = {در ایستگاه‌های تقلیل فشار برای پیش‌گرمایش گاز طبیعی از گرم‌کن‌های گازسوز و برای کاهش فشار از شیر فشارشکن استفاده می‌شود. پیش گرمایش به این دلیل انجام می‌شود که احتمال تشکیل هیدرات گازی حاصل از کاهش دما در خروجی شیر فشارشکن به حداقل برسد. در این تحقیق علاوه بر بررسی لزوم وجود سامانۀ پیش‌گرمایش در جلوگیری از تشکیل هیدرات گازی در روش متداول کاهش فشار در ایستگاه‌های تقلیل فشار معمول، چهار روش جایگزین در ایستگاه‌های پنج شهرستان گرمسیری استان فارس شامل داراب، لار، لامرد، مهر و فراشبند ارائه و شبیه‌سازی شده است. این روش‌ها عبارت‌اند از: استفاده از توربین انبساطی به جای شیر فشارشکن، استفاده از توربین انبساطی به جای شیر فشار شکن و گرمکن برقی به جای گرمکن گازسوز، استفاده از لولۀ گردابی به جای شیر فشارشکن، استفاده از گرم‌کن مبتنی بر سیکل تبخیر- میعان به جای گرم‌کن گازسوز. متعاقب آن، بار حرارتی و میزان گاز مصرفی مورد نیاز برای پیش گرمایش گاز طبیعی برای روش‌های پیشنهادی و روش متداول مقایسه شده است. همچنین میزان کار تولیدی در روش‌های پیشنهادی که شامل توربین انبساطی است، حساب شده است. روش‌های مبتنی بر توربین انبساطی بیشترین و استفاده از لولۀ گردابی کمترین مقدار بار حرارتی و میزان گاز مصرفی برای پیش‌گرمایش گاز را دارد. گرم‌کن مبتنی بر سیکل تبخیر-میعان به‌دلیل بالاتر بودن بازده حرارتی آن نسبت به گرم‌کن گاز سوز (حمام آب غیر مستقیم)، بار حرارتی کمتری نیاز دارد.}, keywords_fa = {ایستگاه تقلیل فشار,شیر فشار شکن,توربین انبساطی,گرم‌کن برقی,لولۀ گردابی,گرم‌کن CWT}, url = {https://www.ijche.ir/article_126241.html}, eprint = {https://www.ijche.ir/article_126241_21009f214a80b149d78e8685ebf6e970.pdf} }